20Rudder pedal or yaw control surface position Full range 2 0.5
Note Sufficient time data is required to permit determination of the relationship between recorded information and Universal Coordinated Time.
Note Sufficient time data is required to permit determination of the relationship between recorded information and Universal Coordinated Time.
All parameters of the FDRIU must be sampled, conditioned, and digitised or reformatted in such a manner as to meet ARINC 717-15 standard signal characteristic.
The FDRIU must have a design assurance level commensurate with the failure condition classification of "minor".
Note The concept of failure condition classification is described in the appropriate certification specification guidance material. For example, EASA AMC 25.1309.
The FDRIU must be tested in accordance with the test conditions mentioned in RTCA/DO-160F.
Software for the FDRIU must be developed in accordance with RTCA/DO178C to Level D as defined in section 2.3.3 of RTCA/DO-178C.
The electronic hardware for the FDRIU that is complex as described in section 1.6 of RTCA/DO-254 must be developed in accordance with RTCA/DO-254 to Level D as defined in Table 21 of RTCA/DO-254.
The materials used in the manufacture of the FDRIU, other than small parts that would not contribute significantly to the propagation of fire, must be selfextinguishing in the event of fire and meet the requirements of Category C of section 26 of RTCA/DO-160F.
Subject to subclause (2), each component of the FDRIU must be permanently and legibly marked with the name of the manufacturer and the number "ATSOC1007b".
Subclause (1) does not apply to a component to the extent that the shape, size or nature of the component makes it impracticable to mark on the component the information required by subclause (1).
If the article manufacturer of the FDRIU supplies 1 or more FDRIUs to a person, the manufacturer must give the person:
at least 1 copy of the technical data mentioned in paragraphs 12 (a) to (f); and
any other data or information necessary for the proper installation, use and continued airworthiness of the FDRIU.
The technical data mentioned in paragraph 21.605 (2) (b) of CASR must include the following:
the operating instructions and equipment limitations for the FDRIU, including full descriptions of the following:
the operational capability of the equipment;
if the applicant requests approval of a deviation from any performance standard mentioned in this Schedule - the operational or installation limitations that would result from that deviation;
the installation procedures for the FDRIU and limitations, including the following:
descriptions of the extent to which the FDRIU, when installed according to the installation procedures, will continue to meet the requirements of this Schedule;
descriptions of any unique aspects of the installation;
as an integral part of the procedures - the following manufacturer's statement:
The conditions and tests required for ATSO authorisation of this article are minimum performance standards. It is the responsibility of the person installing this article on or within a specific type or class of aircraft to determine that the aircraft installation conditions are within the standards set out in ATSO-C1007b. ATSO articles must have separate authorisation for installation on or within an aircraft.
schematic drawings for the installation procedures;
wiring diagrams for the installation procedures;
equipment specifications;
a list of the components that make up the FDRIU, including:
part numbers referenced to the relevant part; and
if applicable - vendor part number cross-references;
an installation manual (IM), a component maintenance manual (CMM) or both an IM and a CMM for the FDRIU that include the following:
information about the periodic maintenance, calibration and repair of the installed equipment for its continued airworthiness;
recommended inspection intervals and service life of the installed FDRIU;
details of any CASA approval to deviate from any performance standard in this Schedule;
technical data for material identification and specifications;
the functional test specifications to be used to test each FDRIU to ensure its compliance with this Schedule;
analysis and test results in relation to the FDRIU to substantiate compliance with this Schedule;
nameplate drawings showing how the FDRIU will be marked in accordance with the requirements mentioned in paragraph 21.607 (1) (c) of CASR and clause 10;
a list of the drawings and processes, including revision level, necessary to define the design of the FDRIU and its components;
an Environmental Qualification Form, as mentioned in RTCA/DO-160F, for each component of the FDRIU;
details of the computer software used in the FDRIU, including the following:
if the FDRIU includes a digital computer - a statement of assurance and accompanying evidence that the software has been developed in accordance with RTCA/DO-178C;
a Plan for Software Aspects of Certification mentioned in RTCA/DO178C;
a Software Configuration Index mentioned in RTCA/DO178C;
a Software Accomplishment Summary mentioned in RTCA/DO178C;
if the FDRIU includes a complex custom micro-coded component:
a Plan for Hardware Aspects of Certification mentioned in RTCA/DO254; and
a hardware verification plan mentioned in RTCA/DO254; and
a toplevel drawing and Hardware Accomplishment Summary mentioned in RTCA/DO254.
Schedule 29 ATSO C1009 - Rescue baskets, cages and enclosures for carrying personnel external to a rotorcraft
(subsection 13.2 (1), table, item 9)
Division 1 - Preliminary
This Schedule applies to an appliance, used as part of a personnel-carrying device system for the carriage of persons external to a rotorcraft, manufactured by an article manufacturer.
In this Schedule:
ANSI/ASSP Z359.12 means the American standard ANSI/ASSP Z359.12-2019: Connecting Components for Personal Fall Arrest Systems, published by the American Society of Safety Professionals and as in force from time to time.
AS/NZS 1891.1:2020 means Australian/New Zealand Standard AS/NZS 1891.1:2020 - Personal equipment for work at height - Part 1: Manufacturing requirements for full body combination and lower body harnesses, as in force from time to time.
attachment point means the point on the rigid structure of a PCDS for connecting to a lifting bridle or similar device.
ASTM F2821-15(2020) means the standard ASTM International - ASTM F2821-15(2020): Standard Test Methods for Basket Type Rescue Litters, published by ASTM International, as in force from time to time.
basket type litter, in relation to a PCDS, means a conveyance (including a stretcher) for the sick or injured, usually consisting of a tubular metal frame enclosing a moulded plastic or wire shell.
EASA CS-25 means the EASA standard Certification Specifications for Large Aeroplanes CS-25, as in force from time to time.
human external cargo means a person that is carried external to a rotorcraft during a human external cargo operation.
bridle means a manufactured or improvised system that attaches the rigid structure of a PCDS to the raising or lowering system.
personnel-carrying device system, or PCDS, means a device or system that has the structural capability and features needed to safely transport human external cargo, including but not limited to:
life safety harnesses; and
rigid baskets or cages, attached to a hoist or cargo hook or mounted to the rotorcraft airframe.
product label means a label or marking affixed to a product by the manufacturer that provides general information, warnings, instructions for care, maintenance, and other information.
relevant welding testing standard means a standard that is similar or equivalent to the standard ISO 24394:2023 Welding for aerospace applications - Qualification test for welders and welding operators - Fusion welding of metallic components, as in force from time to time.
restraint hardware means any component of the restraint system of a PCDS that is not part of the webbing.
soft enclosure, in relation to a PCDS, means a PCDS that uses textiles to fully envelope or contain human external cargo with the following features:
load-bearing textile material;
the cargo is restrained using the structure of the PCDS or internal restraint straps;
the system includes, but is not limited to, rescue vests and valise style bags for rescue of infants.
Division 2 - Minimum performance standards - Rigid structures
Showing the first 12 of 25 provisions. See all provisions